Retro Game Guy

It's the 1980's again!


Leave a comment

Keeping old controllers alive…

Last year, I picked up an Atari 2600, two joysticks, a set of paddles, and ten games at a local thrift store.  The console worked perfectly, but the joysticks were iffy and the paddles all jittery.  I had never re-built an Atari controller before, but I am pretty handy with a soldering iron, so I thought I would try rebuilding these joysticks and paddles myself.

Re-building the joysticks…

The two joysticks were in good physical condition, so I used one of those damp, anti-bacterial cleaning cloths to get all of the dirt and dust off of the outside.  To open up an Atari joystick, just unloosen four screws on the bottom of the joystick and the top will separate from the bottom.  Be careful as fire button and spring will come loose and one of my springs went missing.  There are a few dealers that still have original Atari CX40 joystick circuit boards for sale, but I opted for a re-build kit from Best Electronics.  Best includes a new joystick handle and a new circuit board, with gold contacts, that is an exact fit for the original Atari circuit board.  I had already turned my soldering iron on before I realized that no soldering would be needed as the Atari wiring harness is connected via slide clips.  I carefully removed the wires from the original board and installed them on the new Best gold board.  The Best gold board includes markings that indicate which wire should be connected to each contact.  I then carefully re-assembled the joystick and tested it.  This actually took me a couple of iterations as I didn’t have the spring lined up correctly and fire button wasn’t working.  Also, since I lost a fire button spring, I had imagineer one from a ball point pen spring.  Thus, I highly recommend ordering a couple of those from Best when you order the rebuild kits.  Once I had the springs properly aligned, the joysticks worked perfectly and are now better than new!

Original CX40 Parts

Original CX40 Parts

Gold CX40 PCB

Gold CX40 PCB

Re-building the paddles…

The Atari CX-30 paddles are infamous for becoming ‘jittery’, after many hours of use.  Some people have had success using contact cleaner to solve this problem, but most of the time the potentiometers are just worn out.  As far as I know, it is almost impossible to find original replacement potentiometers for Atari paddles.  Thankfully, Best Electronics has been able to locate a source of replacement ‘super pots’ for Atari paddles that are actually better quality and a perfect fit.  To replace the pots in a set of CX30 paddles is pretty straight forward.  I removed the two screws from the back of the case to separate the case halves.  I then loosened the nut that holds the pot in place and carefully removed it.  I used my soldering iron to unsolder the two wires from the existing pot and, then soldered them to the new super pot.  Using the new nut that comes with the super pot, I re-installed it into the case and re-assembled the case.  I repeated this process for the other paddle in the CX30 set.  Once they were both back together, I tested them and they worked flawlessly, but one of the paddles had a rattle.  I took it back apart and realized that the plastic housing had cracked around one of the screw holes.  Not wanting to wait to order a replacement case, I used a little silicone adhesive and shored up the post with a wire tie.  Problem solved, rattle gone!  The re-built paddles are smooth and jitter free!

Old & New CX40 Pots

Old & New CX40 Pots

Fixing a CX24 joystick…

One of my CX24 joysticks for my Atari 7800 wasn’t working very well, so I had also ordered a replacement circuit board from Best.  It was a simple effort to swap this board, in my failing controller, and restore it to full health.

Overall thoughts…

Fortunately, it is fairly easy to give new life to old Atari controllers.  There is more than one on-line Atari dealer that have repair parts for Atari joysticks and paddles, but Best Electronics seems to have the most complete selection.  Their ‘gold’ joystick circuit boards and ‘super pots’ are easy to install and will give your controllers new life.  Don’t continue to settle for a failing controller and don’t think that your only option is to buy new ones…get some replacement parts and re-build them yourself!

Follow me on twitter…

@Atarigameguy


1 Comment

Atari 7800 missing classics…

The Atari 7800 was planned for release in 1984, but was not actually released until 1986.  By then Atari had lost the momentum to Nintendo and only about sixty games were originally released for the Pro System.  Also, many third party publishers moved on and developed games for the NES.   In the past decade, an active homebrew community has developed and released more than twenty additional games for the 7800, but there are still a lot of holes in the 7800 library.  I think it is interesting to consider the games that should have been developed for the 7800.  Here are my top ten missing classics for the 7800:

Battlezone-Atari made a great version of this game for the  2600 and Activision developed a similar game (Robot Tank) for the 2600 as well.  It would have been awesome to see a simulated vector graphics version developed for the 7800, but a version in the style of either of the 2600 games would have been fine as well.

Defender-Atari made awesome versions of this game for both the 2600 and the 5200.  In fact, the also made Stargate (or Defender II) for the 2600 as well.  Bob DeCrescenzo hacked Defender II to make an almost perfect version of Defender for the 2600 (Defender Arcade) and the Atari 5200 version is widely respected as one of the best games made for the Super System.  Seriously Atari…what were you thinking…where is Defender for the 7800?  At least we can play Bob’s great 2600 game on our 7800’s!

Galaxian-Atari made Galaga for the 7800, so I guess they figured that they didn’t need to make Galaxian as well.  The 2600 version has been hacked and updated into a pretty good game and we can play that version, but it would have been nice to have an official Galaxian for the 7800.

Kangaroo-Atari developed great versions of Kangaroo for both the 2600 and the 5200.  In fact, the 5200 version is almost arcade perfect.  Kangaroo is clearly inspired by Donkey Kong and, maybe since Atari was able to produce Donkey Kong for the 7800, they felt that they didn’t need to develop Kangaroo as well?  Too bad as the 7800 would rock this game!

Millipede-the 7800 version of Centipede is pretty awesome and is a blast to play in the two player cooperative mode.  Millipede is an Atari classic and it is surprising that they never developed a version for the Pro System.  The 7800 was designed to be able to display up to one hundred objects without flicker…Millipede would have been a showcase game for the Pro System.

Missile Command- Given that General Computer Corporation developed the 7800 and they got their start as a company by making upgrade kits for the Missile Command Arcade units, this is one of the most stunning omissions from the 7800 library.  You can certainly play the 2600 version on your 7800, but imagine updated graphics and all three missile bases!

Pitfall-Activision developed two games for the 7800 (Double Dragon & Rampage), but never updated their 2600 classic.  It would be cool to see what could have been done with the 7800’s improved graphic capabilities.  David Crane, we know you are still out there…show us 7800 fans some love…return to your roots and give us an updated version of Pitfall for the Pro System!

Star Raiders-this was an awesome game on both the 2600 and 5200 consoles.  Atari, already had the keypad for the 2600 version which could have been reused for a 7800 version.  A 7800 version of this game would be a blast and could have been a big seller for Atari.

Tempest-it took thirty years, but Tempest was finally completed for the 5200.  One homebrew developer started on a 7800 version, but never completed it.  With the ability to add Pokey chips to the 7800 cartridges, it should have been possible to develop a near arcade perfect port for the Pro System!

Zaxxon-back in the day, I was jealous of Colecovision owners as they had great home versions of both Donkey Kong and Zaxxon.  Atari develop a similar game for the 7800, called Desert Falcon, that is actually pretty good, but not Zaxxon.  Zaxxon is a true ‘80’s arcade classic that should have found its way to the Pro System!

Honorable mention…

One game that I would have included in my top ten would have been Frogger…who played video games in the ‘80’s and didn’t play Frogger?  Up until now, 7800 owners have had to be content playing the Parker Brothers 2600 version of the game.  Fortunately, a near arcade perfect version of Frogger (called Froggie) has recently been developed for the 7800 and should be released later this year.

Froggie 7800

As for the rest of my list…any of you 7800 homebrew developers reading my blog?

Follow me on twitter @Atarigameguy


Leave a comment

My top Atari 7800 games…

It was two years ago this week that I decided, after a long absence, to get back into gaming. After looking at several options for a console, I chose to get a refurbished 7800 and figured that I would pick up 10-12 games for it. Some hundred plus games and four additional Atari consoles later, the 7800 remains my favorite. The ability for the 7800 to play almost all 2600 games is a factor, but it is the Pro System’s capabilities as a home arcade system that continues to draw me to it. While it doesn’t have anywhere close to number of games available as for the NES, it has some of the best arcade ports available for any system. Here are my ten favorite games for the 7800:

Asteroids Deluxe-developed by Bob DeCrescenzo and currently available from AtariAge. The original Atari version of Asteroids (3D Asteroids) for the 7800 is pretty good, but Bob takes it to the next level. Asteroids Deluxe features simulated vector graphics, killer satellites and is about as close to the arcade as you are going to get on a home system. As a bonus, a simulated vector edition of Asteroids is also included (just hold down the pause key when you power up your 7800)!

b*nQ-developed by Ken Siders and currently available from AtariAge. Ken has developed a near arcade perfect port of Qbert for the 7800. Qbert is an arcade classic and Ken’s version is a blast to play and good for hours and hours of fun!

Centipede-one of the original games for the 7800, programmed by General Computer Corporation (the designers of the 7800). The 5200 version of Centipede is probably the closest to the arcade, but the 7800 version is still a great game and a blast to play. One thing that sets Centipede for the 7800 apart is the two player team variation. This game is fun to play, but even more fun with two people. 7800 Centipede carts are plentiful and can usually be had for five dollars or less.

Commando-developed by Dwain Skinner for Sculptured Software/Atari and released in 1989. I prefer the traditional arcade games like most of the ones in my top ten, but Commando stands out for its game play, awesome graphics, and Pokey sound. In order to save space on the motherboard, provisions were made to allow for Pokey sound chips to be added to 7800 cartridges. Unfortunately, due to costs, only two 7800 games actually had Pokey chips in the carts (Ballblazer and Commando). Commando earns its way onto my list as it shows what Atari could have with the 7800. Unfortunately for the collector, Commando is one of the harder games to find.

Dig Dug- another one of the original 7800 games developed by GCC for Atari. This is an awesome port and belongs in every 7800 collection. It would have been better had Atari choose to include Pokey sound, but is still a great game, is a blast to play, and can typically be had for five dollars or less.

Donkey Kong XM (or PK)-by Perry Thuente. The best port of Donkey Kong for any home console…period. See my recent post about this awesome game. Perry spent more than a year developing the most accurate port of Donkey Kong …ever! The only way to get a better version of Donkey Kong at home would be to buy your own arcade cabinet!!!

Galaga-yet another one of the original 7800 games developed by GCC for Atari. The 7800 version is probably one of the best ports available for a home console. Even with all of the motion on the screen, there is no slow down and no flicker. This game is a blast to play and can typically be had for five dollars or less.

Moon Cresta- developed by Bob DeCrescenzo and currently available from AtariAge. If you like Galaga, you will love Moon Cresta. Bob to great efforts to get the alien movements as close to the arcade version as possible. Even on the ‘easy’ setting, Moon Cresta is a challenging game that will have you hitting the reset button over and over.

Pac-Man Collection- developed by Bob DeCrescenzo and currently available from AtariAge. I get to cheat here as this cart includes a whole bunch of Pac-Man games including: Pac-Man, Pac-Man Plus, Hangly Man, Ms. Pac-Man, and Ultra Pac-Man. Bob had originally developed these separately, but with efficient programming, he was able to squeeze them all onto a single 32K cart. This cart will give you hours and hours of fun and belongs in every 7800 collection!

Space Invaders- developed by Bob DeCrescenzo and currently available from AtariAge. Like most everyone that had an Atari 2600 in the early 80’s, I played Space Invaders over and over again. The 2600 version was actually pretty darn good, but Bob shows how great the 7800 can be as a home arcade system. His version totally rocks and has all kinds of options such a moving shields, zigzagging bombs, and invisible invaders.

Space Invaders for the Atari 7800

Space Invaders for the
Atari 7800

Ok, I am going to cheat a little and have a couple of honorable mentions:

Alien Brigade-developed by Ken Grant for Atari. One of the later releases for the 7800 (and challenging to find), Alien Brigade is an awesome game with outstanding graphics. It is the best of the five light gun games developed for the 7800 (although it can also be played with a normal controller). Atari never released the light gun for the 7800, so you will have to find an XEGS model or get one from Best Electronics.

Plutos-developed by Kevin Franklin at Tynesoft and never officially released. An unstable prototype was discovered by Curt Vendel in 2008 and Bob DeCrescenzo, Mitchell Orman, and Eckhard Stolberg collaborated to get the code stable on stock 7800 consoles. The graphics in Plutos (and its sister game Sirus) are stunning and really show what the 7800 is capable of. Had this game been released in the 80’s, it would have been a top seller for sure!

Overall thoughts…

More than half of my favorite 7800 games are homebrews by Bob, Perry, & Ken. It is really amazing that, some thirty years after the 7800 was designed, new games are still being developed. In fact, several new games have been recently finished and will be released soon. It also shows that had Atari released the 7800 in 1984, as originally planned (vs. 1986), that many more games probably would have been made available.

Follow me on Twitter:  @Atarigameguy

 


1 Comment

Donkey Kong…

Donkey Kong is a 1981 video game developed by Nintendo and is one of the earliest successful platform games. Although there had been a couple of other platform arcade games, Donkey Kong was the first to introduce jumping.  Programmed by Shigeru Miyamoto, Donkey Kong was a monster hit that established Nintendo as a serious player in the video game market.  There are four different ‘platforms’ in Donkey Kong:  The construction scene, the cement factory, the elevator scene, and the rivets screen.  The goal in Donkey Kong is, essentially to climb to the top of the screen and rescue Pauline.  Only in the rivets screen is this different where Mario needs to knock out all of the rivets.

At the time that Shigeru developed Donkey Kong, it was a radical departure from the space shooters and maze games that had been dominating the video game market.  In fact, Nintendo America was not sure that it would be successful.  The Nintendo America staff is credited with naming the characters in Donkey Kong.  Originally they were only known as Jumpman and Lady.  They renamed them Mario and Pauline and had graphics made for American versions of the arcade cabinets.  They tested a couple of Donkey Kong arcade units in a couple of bars and, much to their surprise, the public loved the game.  They ended up converting over 2000 surplus arcade units into Donkey Kong units and the rest is history.  Donkey Kong went on to become one of the most popular and most recognizable game franchises in history.

Donkey Kong was ported to a number of home game consoles and computers including the Colecovision, the Atari 2600 and 7800’s, the Intellivision, and the Atari 8-bit computer line.

Colecovision version…

Coleco won the rights to produce cartridge based home console versions of Donkey Kong and decided to make it the ‘pack in’ game for their system which helped them sell over six million consoles.  The Colecovision (CV) version of Donkey Kong featured three of the arcades screens (the cement factory was left out home console versions) and no climbing or intermission screens.  The graphics were impressive, but the game was a little too easy to play.  In the elevator screen, Kong doesn’t throw any barrels, which makes this screen incredibly easy compared to the arcade version.  Still, the CV version was impressive for the time (1982).  Coleco also ended up producing Donkey Kong for the Atari 2600 and Intellivison.

Donkey Kong for the Colecovision

Donkey Kong for the
Colecovision

2600 version…

Gary Kitchen programmed the 2600 version of Donkey Kong for Coleco.  I had the chance to meet Gary last year and hear him talk about the development of this game.  He was only authorized to make a 4K non-bankswitched game, so he was very limited with what he could do.  He managed to get two levels (Construction and Rivets) into the 2600 version, but the graphics (impressive for the 2600) were no match to the CV version.  Gary managed to capture essence of Donkey Kong, but it is not one of the better games for the 2600.

Today, there are two new homebrew 2600 efforts underway:   Donkey Kong Arcade and Donkey Kong VCS.  Both feature improved graphics and sound, all four screens, and intermissions.  The developers of these games have taken different approaches, but both are creating awesome versions for the 2600.  Due to Nintendo’s licensing policies, these will probably not be able to be made commercially available, which is a real shame.  However, if you have a Harmony cart, you can try out the prototype versions of these games on your 2600.

Donkey Kong for the Atari 2600

Donkey Kong for the
Atari 2600

5200 (8-bit) version…

Coleco did not develop a 5200 version of Donkey Kong, probably as they saw the 5200 as the main competitor to the CV.  Fortunately, Atari had obtained the rights to produce home computer versions of the game and developed an excellent port for their 8-bit line.  Atari’s 8-bit version has all four screens and well as the ‘how high’ intermission screens.

The 8-bit version has been converted to run on the 5200 and can be played on the Atarimax cart or can be obtained in cart form.  Playing Donkey Kong with the 5200’s analog joysticks takes some adjustment, but it turns out to be one of the better games for the Super System.   The game also takes advantage of the 5200’s Pokey chip to produce near arcade quality sound.

Donkey Kong for the Atari 5200

Donkey Kong for the
Atari 5200

7800 version…

The 7800 version of Donkey Kong was released in 1988 and is an excellent good port of the game.  As with all of the home console versions, it is missing the Cement Factory screen as well as the climbing and intermission screens.  Also, like most 7800 games, the sound could have been better had Atari included a Pokey chip in the cartridge.   Even with these limitations,  the 7800 version of Donkey Kong is probably the best original port of the game for a home console and demonstrates the 7800’s home arcade capabilities.

Thirty years after the release of the 7800, a new version of Donkey Kong is now available for the Pro System.  Perry Thuente spent over a year working on improving the 7800 version.  Originally, he had only intended to develop a version that would improve the sound by taking advantage of Atari’s Pokey chip that will be in the XM expansion module.  One thing led to another, and Perry ended up completely re-building the game.  He has added the climbing and intermission screens as well as the missing cement factory level.  He also improved the graphics and added the ability to play the game in either the Japanese or US arcade order.  Perry’s version is called Donkey Kong XM and needs the XM module in order to hear the sound.  Unfortunately, the delivery of the XM module has been delayed.  Also, due to Nintendo’s licensing policies, Perry can’t make this commercially available and is only making a few copies of the game for friends.  Since the XM module has been delayed, Perry has made a handful of Donkey Kong PK cartridges which take advantage of CPUWIZ’s Versaboard and include a Pokey Chip.  This version produces arcade quality sound on a stock 7800.  Being one of the lucky ones to have a copy of Donkey Kong PK, all I can say is wow!  The only way to have a better home version of Donkey Kong would be to put an actual Donkey Kong arcade cabinet in your house!!!

Donkey Kong XM for the Atari 7800

Donkey Kong XM for the
Atari 7800

Overall thoughts…

If you are a Donkey Kong fan, there are no really bad versions of the game and they are all readily available.  The Colecovison, 2600, and 7800 versions are plentiful and cheap, but a copy of the 5200 version on cart will set you back a few $$$ (however, is a pretty awesome game for the 5200!).

Perry’s Donkey Kong XM or PK version is, however in a league by itself.   If you own a 7800, and are a fan of Donkey Kong, then you simply need to get yourself a copy of this game.  Make friends with Perry and convince him to make you a copy.

Also, if you are a 2600 fan, don’t forget about the new versions of Donkey Kong that are nearing completion!

@Atarigameguy


Leave a comment

Xevious…

Xevious is a 1983 arcade game developed by Namco and released by Atari in the US.  Xevious is a top down, vertical scrolling space shooter developed by Masanobu Endo.  The game was designed to run on Namco’s Galaga hardware with 3 Z80CPU’s and a Namco sound chip. It was a monster hit in Japan, but never achieved quite the same success in the US.  Xevious was ported to a number of game and computer systems of the era including the Atari 7800, the NES, and the Commodore 64.  Versions were planned for the Atari 2600 and 5200, but never released.

In Xevious, you must pilot your ship called a Solvalou against various enemy air and ground targets, including tanks, stationary bases, flying mirrors, and black spheres (8-balls).   The Solvalou is equipped with both a zapper for air targets and a blaster for ground targets.  There are sixteen areas in Xevious and the game loops back to area seven, if you are able to clear all of the areas.  One of the cool things about Xevious is that if your are 70% of the way or better through an area and are ‘killed’, the game restarts at the beginning of the next area.  The terrain in Xevious varies from dense forests, to rivers and oceans, to developed areas.  This makes for a variety of background graphics and adds interest to the game.  Another interesting thing about Xevious is that you don’t really have to ‘kill’ anything to keep advancing.  If you can manage to fly your Solvalou through the game and not get ‘killed’, you can advance through the entire game without shooting anything.

2600 Version…

The 2600 version of Xevious never made it past the prototype stage.  Programmed by Tod Frye  of 2600 Pac-Man fame, it had the beginnings of a pretty good port.  Tod was able to accomplish the scrolling background (all be it with simplified graphics) and have multiple enemies on screen, with little to no flicker.  Of course the 2600 has only one fire button, so Tod had the CX-40 fire button do double duty and it fires both missiles and bombs.

Tod had managed to get four types of enemies programmed (discs, mirrors, 8-balls, & tanks) into his 2600 version before the plug was pulled by Atari, during yet another management shake-up.   Hopefully, one day, one of the 2600 homebrew programmers will develop a new version of Xevious.  With today’s cart technology, it should be possible to develop a great version of this classic for the 2600.  For more information on the 2600 version of Xevious, check out Atariprotos.com.

2600 Xevious Prototype

2600 Xevious Prototype

5200 Version…

The 5200 version of Xevious was programmed by Jim Huether in 1983, but never formally released by Atari.  Happily, the final prototype version has been preserved and made available to the gaming community.  It is really unfortunate that the 5200 version was never released as it is complete and it is a pretty good game.  Jim managed to program almost all of the arcade’s enemies and the sound effects are nearly spot on.  The two biggest complaints about the 5200 version are that the graphics seem a little ‘washed out’ and your bullets appear as ‘bars’.  Other than these two complaints, Xevious is an awesome game for the 5200.  It is a shame that Atari never formally released it, but thankfully, the prototype code was preserved and is playable on the Atarimax multi-cart.  For more information on the 5200 version of Xevious, check out Atariprotos.com.

Xevious for the Atari 5200

Xevious for the Atari 5200

7800 Version…

The Atari 7800 version of Xevious is the only officially released version for the Atari home console family.  Programmed by Tom Flaherty of General Computer Corporation, it was intended to be one of the launch titles for the 7800 (had it been released as planned in 1984).  Tom did an outstanding job porting Xevious to the 7800 and his version includes almost all of the enemies and features of the arcade version.  The graphics are extremely well done, colorful, and crisp.   Also, the sound is pretty good for a standard (non-Pokey) game.  The 7800 version of Xevious can be played with either the two button Pro-line joystick or a regular CX-40.  When using the Pro-line, one fire button controls the Zapper (missiles) and the other the Blaster (Bombs).  When using the CX-40, both missiles and bombs are fired at the same time, like in the 2600 prototype.  I had owned a copy of Xevious for nearly two years before I realized that it could be played with a standard CX-40.  This is not something that Atari included in the Xevious manual, but I think it definitely makes the game more enjoyable to play!

Xevious for the Atari 7800

Xevious for the Atari 7800

Overall thoughts…

The 2600 version is clearly an unfinished prototype and is interesting, but not really anything to get worked up about.  Both the 5200 and 7800 versions are excellent ports and deserve a place in your collection.  While you will need the Atarimax multi-cart to play the 5200 version, the 7800 version is easy to find and normally can be had for less than five dollars.  If you have a 7800 and don’t have a copy of Xevious, you should pick one up the next time you visit your local retro game shop!

@Atarigameguy


Leave a comment

Hardware Happenings…

2014 is the 30th anniversary of the Atari 7800’s release and there are some amazing things happening…

AtariAge member CPUWIZ has been busy developing new cartridge boards for 7800 games. He has developed a board that can hold up to 1MB of memory, which will allow for some amazing new games to be developed.  He has also teamed up with RevEng (another AtariAge member) to develop some cool multi-carts for the 7800’s.  One of these has a new bankswitching scheme to allow 8 128K games to live on the same cart.  He has also gotten the green light from Bob ‘PacManPlus’ DeCrescenzo to develop a limited edition multi-cart with 8 of Bob’s 7800 ‘homebrew’ games on it.

Curt Vendel has been working on the Atari 7800 expansion module for over three years and hopes to release it soon.  This expansion module contains both Pokey and Yamaha audio chips, expanded memory, and high score keeping.  At the Portland Retro Game Expo last October, AtariAge had one of Curt’s prototype units in operation showing off the unit’s capabilities.  It was amazing to hear the difference that Pokey sound made for Donkey Kong!

Fred ‘Batari’ Qimby has also been hard at work on a new SD multi-cart for the 7800.  Previously known as the H2, Fred’s new cart will now be called the Concerto cart and he hopes to have it ready by the Portland Retro Game Expo this fall.  Fred hopes to be able to have the Concerto be able to host and play any 2600 or 7800 game on an Atari 7800.

With all of these new hardware developments, 2014 may shape up to be the best ever for the Atari 7800.  Amazing for a 30 year old system!

Flashback Fever…

ATGames will be releasing the Atari Flashback 5 in October.  Hardware wise, it is expected to be similar to the Flashback 4 with wireless controllers.  This time around, it will have 100 games built in.  The final game list has not yet be released, but let’s hope it now also includes games like Berzerk, Defender, and Midnight Magic!

ATGames has also announced that they will produce both an Intellivison and ColecoVison Flashback unit.  Both of these units with feature 60 built in games and overlays for the controllers, but the game list has not yet been released.  It is probably not likely, due to Nintendo’s licensing practices, but the ColecoVison Flashback with Donkey Kong built in would be killer!

As soon as more is know about the details of these Flashback units, I will be sure to post an update!

@Atarigameguy


1 Comment

Atari Retro-game Happenings…

It is hard to believe that in 2014, multiple new games for the Atari systems are under development.  Here is just some of the current game news…

2600…

There are several outstanding games in the works for the 2600.  A couple of the most notable are Star Castle Arcade and Stay Frosty 2.  These two games are complete and will be released as soon as enough cart boards are available for a production run.  Several other homebrew games are also in the works including Circus AtariAge, Frantic,  and Zippy the Porcupine.

5200…

Just after I posted my last blog about Caverns of Mars, two developers (Paul Lay & Aking) converted Caverns of Mars 2 and 3 to the 5200.  Caverns of Mars 2 is a side scroller very similar to Scramble and lots of fun to play on the 5200.  Caverns of Mars 3 (Phobos) is very similar to the original game, but with improved graphics.  If you are a C of M fan, then you should head over to AtariAge and check out these 8-bit conversions!

Speaking of 8-bit conversions, Paul and Aking have converted more than dozen 8-bit games to the 5200 in the past few weeks.  In addition to Caverns 2 and 3, they have converted titles such as Ant-Eater, Bacterion, and Pooyan.   Thanks to Paul, Aking, and a few others, 2014 is turning out to be a banner year for the 5200!

7800…

Master 7800 programmer Bob ‘Pac-Man Plus’ DeCrescenzo has recently completed Astro Blaster and is now working on a port of KC Munchkin.   Bob plans to make a cart run of Astro Blaster as well as a run of ‘Bentley Bear: Crystal Quest’ in the next few weeks.

Donkey Kong…

2014 may go down as the year of Donkey Kong for Atari Systems.  Perry Thuente has recently completed one of the most accurate ports of Donkey Kong (Donkey Kong XM) for any home system.  He spent months updating the 7800 version to be as arcade accurate as possible.   His version has all four screens (only three were included originally) and Pokey sound (requiring the soon to be released 7800 expansion module (XM)).   Perry has been busy assembling over 100 carts and may also release a Pokey cart version that will run without the XM.

No less than two different 2600 versions of Donkey Kong (Donkey Kong Arcade and Donkey Kong VCS) are under development.  Both versions are absolutely amazing and totally blow away the original version for the 2600.  It is absolutely amazing to see what can be done with the venerable 2600!

Wow…

It is hard to believe that so many great games for the Atari 8-bit game systems are going to be available in 2014…it seems like the 2600, 5200, and 7800 will live on for many years to come!

@Atarigameguy

Follow

Get every new post delivered to your Inbox.